Super PDR 12V White Hot Melt Glue Gun For Hot Adhesive Glue Stick Glue Rods Dent Pulling Bridge Paintless Dent Removal Tools Kit

Super PDR 12V White Hot Melt Glue Gun For Hot Adhesive Glue Stick Glue Rods Dent Pulling Bridge Paintless Dent Removal Tools Kit
  • Продавецguaranteedautos.us
  • Список ценUS $35.12piece
  • Продажная ценаUS $35.12piece
  • ДоставкаБесплатная доставка
  • Рейтинги4,9 (405)

Oписание продукта

NEW Mini High Pressure OCA Adhesive Sticker LCD Bubble Remove Machine+OCA Vacuum Laminator Machine for 7 inch Screen Repair

 

gvrewag

 

Notice:

this machine need Air Compressor and Vacuum Pump ,so if you buy it ,You need to purchase a vacuum pump and Air Compressor

 
1.Safety Rule
For your own safety, please read this manual carefully. Please familiar with the application and limitation of the machine, as well as the relevant potential risk.
A. please read this manual carefully before using the machine.
B. Please keep the grounding good, bad grounding may result in equipment damage or endanger personal safety.
C. It is strictly forbidden to open the electric box as non-professionals.
 
2.Specification

No.1 Laminating Machine

Voltage: AC220V (AC110V Optional)

Working Environment: 20-30 degree, Clean, Dust-free

Heating Mode: Constant temperature heating

Machine Size: 310*310*430mm

Net weight: 35KG

Power: 500W

 

Bubble Remover

Voltage: AC220V (AC110V Optional)

Working Environment: 20-30 degree, Clean, Dust-free

Heating Mode: Constant temperature heating

Machine Size: 300*330*370mm

Net weight: 16KG

Power: 20W

 

For laminator, it is recommended to use no less than 300W of the vacuum pump, and not less than 18L of air compressor.

For bubble remover, it is recommended to use no less than 18L of air compressor. ( Laminator and bubble remover can be shared with one air compressor. )

 
3.Features

1) NO. 1 laminating machine built-in display parameters controller, operation simple and clear;

2) Bubble remover door design for a second switch, built in air lock with safety device.

 

4.Installation

1) For laminator: Plug in, and put the vacuum pump triangl plug into the triangl port while put the vacuum tube into the under port. As the photo shows.

 

vsdvz

 

2) Insert the air compressor pipe to the pressure regulating valve interface back of the laminator.

 

dfedd
 
 
3) For bubble remover: Insert the air compressor pipe to the pressure regulating valve interface back of the bubble remover. Open the air compressor power and open the outlet switch.
 
 
FEWGFV
 
Attention: ( Use special joint to divide the compressor pipe into two sections. Put one into laminator interface, put another on into bubble remover interface.)
 
gvbeabhfgvb
 
 
 
5.Operation
 
 
1
 
 
Open the laminating door, put the aligned screen into the machine.
 
 
2
 
 
 
 
Open the door and click start button, the vacuum pump will automatically working. Pressing plate will auto-pressing after vacuumizing in prescribed time. After laminating, open the door.
 
 
 
 
3

 

 

 

Take out the screen and test for it

 

 

4

 

 

Rotating left to open the defoaming doors, out the screen inside. Close the door, Rotating it tom the right for locks, press the start button, air compressor stars automatically and the pneumatic cylinder inflated to 0.6 MPa. Wait for the prescribed time, the cylinder will automatic discouraged. Open the door and take out the screen.

 

Attention: Defoaming time can be set freely, usually for 5 to 10 minutes, depending on the bubble size.

 

6.Maintenance

Items

Notes

Platform & Pressing Plate

Keep clean, no clutter inside.

Life of machine

For keep it long use, turn off the power when not in use.

 

HTB1CKkxKVXXXXcCaXXXq6xXFXXXaHTB1l5QBKVXXXXc9XVXXq6xXFXXXDHTB1YpQvKVXXXXXoapXXq6xXFXXX7HTB1lPkJKVXXXXc3XFXXq6xXFXXXWHTB1NAZTKVXXXXXEXpXXq6xXFXXXBHTB10lwRKVXXXXa1XpXXq6xXFXXXG